Page 632 - MARCACORONA CATALOGUE 2018

Installation, use, cleaning and maintenance manual (1)

Marca Corona ceramics are the outcome of a production process that envisages the use of top quality raw materials, cutting-edge technology and the manufacturer’s instructions for installation of slabs on raised pedestal systems may result in serious injury. For further information and recommendations concerning the
maximum attention towards quality. installation systems please refer to Ceramiche Marca Corona website or to the 20mm catalogue “HiThick”.
The result is a product with a great aesthetic and technical prestige that can offer you the best performance and durability upon condition that the follow-
ing instructions for installation, use, cleaning and maintenance are followed. Instructions for project engineers and customers
If the application of the 20 mm slabs foresees the ceramic product used in structural installations, the project engineer and/or customer must carefully assess the
INSTALLATION project requirements with regard to the technical specifications of the slabs. To prevent the risk of damage or injury, the manufacturer recommends:
Before installation • With regard to a raised floor installation a ceramic slab may fracture on impact if a heavy object falls on it from any significant height. Therefore the manufacturer
Being a professional operator, the tile fitter, who first “sees” and “handles” the tiles, must: recommends to check the specific intended use before starting the installation and to follow table for raised installation provided below. In certain conditions, reinforcing
• report to the purchaser and project engineer any visible defects (see table below) on the ceramic material; must be applied on the back of the slabs (Fiber-Mesh Plus) supplied and applied by the manufacturer;
• With reference to any dry installation system of flooring above the ground level, the manufacturer recommends to comply with local regulations and conditions of use
CASUALE DESCRIZIONE ECCEZIONI with regard to wind-load, loadbearing, seismic events, etc.
Tiles with dimensions (width/length) that are different from those of tiles belonging to the same Failure to comply with these recommendations may lead to improper use of the product and could cause serious damage or injury.
Caliber lot (Caliber), and with deviations above the tolerance ranges indicated in the technical data -
sheet.
Concave or convex tiles (corner curving), with corners curving up or down (warpage) and
Flatness - SIZE up to 2 cm / ¾” from 2 cm / ¾” to 10 cm / 4” from 2 cm / ¾” to 10 cm / 4”
with deviations above the tolerance ranges indicated in the technical data sheet.
Squareness - straightness Tiles with sides that are not straight and that do not form a square (“trapezoid effect”), with - 60x60 cm / 24”x24” Rect. (rated) 4 supports 2 4 supports 2 4 supports + Fiber - Mesh plus
2
of sides deviations above the tolerance ranges indicated in the technical data sheet. 4 supports per slab (3,4 pz/m ) (3,4 pz/m ) (3,4 pz/m )
Tiles with a different thickness with respect to the other tiles in the same box, with deviations 45x90 cm / 18”x36” Rect. (rated)
Thickness - 6 supports 6 supports 6 supports + Fiber - Mesh plus
above the tolerance ranges indicated in the technical data sheet. 60x120 cm / 24”x48” Rect. (rated) (6 pz/m ) 2 (6 pz/m ) (6 pz/m )
2
2
Tiles with cracks that are parallel to or at a right angle with the edges, or surface cracks 6 supports per slab
Cracks -
resulting in immediate detachment of chips after tapping.
Chipping Tiles in boxes, which feature broken corners and/or edges. - FOR THE USA, CANADA AND OCEANIA MARKETS ONLY
Suction cup marks, which are SIZE up to 2 cm / ¾” more than 2 cm / ¾”
only visible for a few seconds in
Tiles with holes, pinholes, craters, bumps, contaminated bodies and tile bottom face damp conditions, are not deemed 60x60 cm / 24”x24” Rect. (rated) 4 supports
Surface defects
appearing on the top face. to be tile defects since, during 4 supports per slab (3,4 pz/m ) 2
normal conditions of use, they are Contattare marca Corona
not visible. 45x90 cm / 18”x36” Rect. (rated) 6 supports
Decorating defects Tiles with screen-printing or glazing defects, drips, stripes resulting from digital decoration,… . - 60x120 cm / 24”x48” Rect. (rated) (6 pz/m ) 2
Tiles with tones that differ in a substantial manner from the reference and/or sample tile 6 supports per slab
Tiles outside the tone range -
supplied to the customer.
Tiles within the same lot with differences in tone that do not comply with the V-shade shown
Mixed tones - NOTE: For any detail and technical specification concerning the fiber mesh plus please contact Marca Corona is responsible only if it supplies the whole
in the catalogue.
system (tile + fiber mesh plus or galvanized sheet). Marca Corona cannot be held responsible for reinforcing systems that as not supplied. In case of break-
Tiles with too many “holes”, colour surfacing out from the body, scratched and/or opaque
Honing/polishing defects - age, tile must be replaced inmediately.
edges, semi-circular surface scratches...
Important Notice: For further details about HITHICK in 20mm thickness and in particular for recommendations, instructions and restrictions to use and instal-
• After installation, Ceramiche Marca Corona will accept no complaints relating to visible defects. lation, please visit the www.marcacorona.it website or refer to the “ Hithick” catalogue.
• Follow a tiling pattern based on a specific installation technique (closed, minimal or open joint, parallel or diagonal installation, continuous or staggered joints, etc.);
before proceeding with installation, the fitter is recommended to show the end customer an example of how the tiles will be installed (by placing them in accordance to the Spreading adhesive and installation: precautions
installation pattern “dry” and without using grout) and to ask for an approval, preferably written. The use of a suitable adhesive is essential for installation. For the installation of ceramic tile, follow the indications of leading adhesive manufacturers.
Light differences in tone are a typical characteristic of some ceramic products. As a general rule, the most suitable adhesive is found by taking the following factors into account:
Ceramiche Marca Corona recommends installation with slabs offset by 1/3 at the most and a grouting joint of at least 2.0 mm for single sizes and 2.0/3.0 mm for Type of support I Type and size of tile I Intended use (floors/walls - indoor/outdoor) I Climatic conditions during installation I Time needed to put tiling
combined sizes. in conditions of use.
• For outdoor installation, tiles must be installed with an open joint (at least 3.0 mm). For extra large tiles installed at a height of over 3 metres, some international standards set forth the necessity to install with a system featuring both adhesive
• Make sure that the supporting surface is perfectly cured, flat and thoroughly clean. and mechanical hooks to be chosen based on the weight of the tile, on the height of the paving and on work site conditions.
Cleaning during installation Spread the adhesive on the bed using a suitably toothed trowel.
In order to obtain the best results in terms of chromatic effect, pick tiles from different boxes. Exert sufficient pressure on the tiles to ensure wetting of at least 70% of the total tile surface.
During installation, the fitter must report any imperfections of the supporting surface (steps or small different in level between adjacent tiles, etc.) and ask for a written When installing in interior commercial environments or outdoors, it is of the utmost importance to spread adhesive both on the tile face and the support
authorisation to proceed work from the end customer or the person in charge of the work site. (double-spreading) so as to avoid gaps between the ceramic tile and the support.
As far as is practicable, the end customer must ensure that the micro-climatic and lighting conditions of the work site allow fitters to perform installation in a reliable manner
and to check that materials and installation are as described above. Recommended grouts
During the time running between conclusion of installation work and delivery to the end customer, ceramic tiling must be:
• kept clean from cement, sand, mortar and any material that could cause staining and/or mechanical surface abrasion; It is important to use a grout that is suitable for the intended use of the tiling.
• protected against damage and soiling due to the work performed by other workers at the site (painters, electricians, woodworkers, etc.). Follow the indications of leading grout manufacturers.
For details, precautions and warnings relating to storage, handling, cutting and installation of the 120x240 size, please see our Tutorial 120x240 Warning:
- available at the address https://www.marcacorona.it/project-division/grandi-lastre.html - or the video tutorials 120x240 on our AFTER INSTALLATION, CERAMICHE MARCA CORONA:
Marca Corona YouTube channel - https://www.youtube.com/user/MarcaCorona1741 • is not responsible for the quality of the tiled area but only for the characteristics of the material supplied.
It is highly recommended to keep several spare tiles for any repair work or as samples in the event of complaints.
Hithick 20mm. Warnings for laying on raised floors.
Wind and breakage warning
Outdoor pavings installed unglued above the ground level are subject to the action of the wind, with the risk, in some cases, of becoming airborne. The manufacturer (1) Reference standards:
recommends to require the assistance of a qualified professional in order to check the suitability of the installation system above the ground adopted, in accordance with • UNI EN 14411 - 150 13006
the local laws and regulations and the conditions of use. Failure to do so could result in serious injury or property damage. A ceramic slab installed on a raised pedestal • UNI EN ISO 10545 - 2
system may fracture on impact if a heavy object is dropped onto it from a height, with a risk of injury to anyone standing or walking on such slab. Failure to adhere to the • UNI 11493 - 1
174 175